Sealing applications with adhesion to PA

Processing Method:
Injection Molding
Color / RAL DESIGN:
black
 
 
Availability:
Globally
Manufacturing Site:
Germany, Malaysia, United States

Typical applications

  • Seals
  • Fastenings
  • Grommets
  • Cable clips
  • Membranes

 

Material features

  • Adhesion to PA6 and PA6.6, up to 50% glass fiber
  • Optimized compression set
  • Optimized flow properties

 

Regulations / Approvals

  • VW 50123
  • BMW GS 93042
  • Mercedes-Benz DBL 5562
  • Renault 03-10-104
  • UL 94 HB

 

X

SHARE FILE

Send
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
Americas (English) PDF fileSafety Data Sheet
Asia (English) PDF fileSafety Data Sheet
Asia (中文) PDF fileSafety Data Sheet
Asia (한국어) PDF fileSafety Data Sheet
Asia (日本語) PDF fileSafety Data Sheet
Value Unit Standard
Hardness 75 Shore A DIN ISO 48-4
Density 1.100 g/cm3 DIN EN ISO 1183-1
Tensile Strength1 9.0 MPa DIN 53504/ISO 37
Elongation at Break1 450 % DIN 53504/ISO 37
Tear Resistance 24.5 N/mm ISO 34-1 Method B (b) (Graves)
CS 72 h/23 °C 29 % DIN ISO 815-1 Method A
CS 24 h/70 °C 44 % DIN ISO 815-1 Method A
CS 24 h/100 °C 61 % DIN ISO 815-1 Method A
Adhesion to PA 62 7.0 (D) N/mm VDI 2019 two-component injection molding
Adhesion to PA 6.62 8.0 (D) N/mm VDI 2019 two-component injection molding
1Deviating from ISO 37 standard test piece S2 is tested with a traverse speed of 200 mm/min.
2The adhesion quality depends on mold design, product geometry and process parameters.
All values published in this data sheet are rounded average values.
The expected shelf life of the TPE granules is a minimum of 24 months from the date of delivery, provided that the storage instructions are followed and the product is kept in the unopened original KRAIBURG TPE packaging.
Dry conditions at room temperature (below 40 °C/ 104 °F), away from heat sources and direct sunlight, must be maintained for proper storage. Contact with nitrogen oxides during storage should be avoided.
For further information and individual custom solutions please contact our customer service.

Processing Guideline Injection Molding
Cylinder Temperature PA 6: 230 - 250 - 260 °C , max. 270 °C (450 - 480 - 500 °F, max. 520 °F) PA 6.6: 245 - 260 - 270 °C , max. 280 °C (470 - 500 - 520 °F, max. 540 °F)
Hotrunner Hot runner temperatures: PA6 max. 270 °C (520 °F); PA6.6 280 °C (540 °F) The runner should be empty after a maximum of 2 - 3 shots.
Injection Pressure 200 - 1000 bar (2900 - 14504 psi) (depending on the size and weight of the part).
Injection Rate In general, the fill time should not be more than 1–2 seconds.
Hold Pressure We recommend to derive the optimum hold pressure from determining the solidification point, starting with 40 % - 60 % of the required injection pressure.
Back Pressure 20 - 100 bar; if color batches are used, higher back pressure is necessary.
Screw Retraction If an open nozzle is used processing with screw retraction is advisable.
Mold Temperature The mold temperature depends on the hard component. A temperature exceeding 80 °C (175 °F) should be avoided. The common temperature is 40 - 60 °C (105 - 140° F).
Predrying To achieve optimum mechanical values, drying the material for 2 - 4 hours at 60 - 80 °C (140 - 175 °F) is recommended.
Needle Valve With materials < 50 Shore A the use of a needle valve is advisable.
Screw Geometry Standard 3-zone polyolefine screw.
Residence Time The residence time is to be set as short as possible with a maximum of 10 minutes.
Cleaning Recommendation For cleaning and purging of the machine it is appropriate to use polypropylene or polyethylene. Machine must be PVC-free.
The expected shelf life of the TPE granules is a minimum of 24 months from the date of delivery, provided that the storage instructions are followed and the product is kept in the unopened original KRAIBURG TPE packaging.
Dry conditions at room temperature (below 40 °C/ 104 °F), away from heat sources and direct sunlight, must be maintained for proper storage. Contact with nitrogen oxides during storage should be avoided.