Applications with increased demands on UV resistance; adhesion to PP

Processing Method: Injection Molding
Color / RAL DESIGN: black

Typical applications

  • Roof racks
  • Static window encapsulations
  • Water deflectors
  • Bumpers
  • Cowls gaskets
  • Function and design elements
  • Automotive Exterior
  • Door sills

 

Material advantages

  • Weather resistant, suitable for automotive exterior
  • Optimized flow properties
  • Surface mapping
  • Optimized mechanical properties
  • Adhesion to PP
  • In-process recycling possible
  • Temperature stability up to 100 °C

 

Regulations / Approvals

  • 49 CFR §571.302 (FMVSS 302)
  • PV 3930 Florida (1 year)
  • PV 3930 Florida (2 years)
  • PV 3929 Kalahari (1 year)
  • PV 3929 Kalahari (2 years)
  • Outdoor Weathering Florida 24 month SAE J1976
  • Outdoor Weathering Arizona 24 month SAE J1976
  • VW 50123
  • BMW GS 93042
  • Daimler DBL 5562
  • PSA B62 0300
  • GM GMW 16233

 

X

SHARE FILE

Send
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
EMEA (English) PDF fileSafety Data Sheet
Americas (English) PDF fileSafety Data Sheet
EMEA (Deutsch) PDF fileSafety Data Sheet
Asia (English) PDF fileSafety Data Sheet
EMEA (Français) PDF fileSafety Data Sheet
Asia (中文) PDF fileSafety Data Sheet
EMEA (Italiano) PDF fileSafety Data Sheet
Asia (한국어) PDF fileSafety Data Sheet
EMEA (Español) PDF fileSafety Data Sheet
Asia (日本語) PDF fileSafety Data Sheet
EMEA (Polski) PDF fileSafety Data Sheet
Value Unit Standard
Hardness 55 Shore A DIN ISO 48-4
Density 0.980 g/cm3 DIN EN ISO 1183-1
Tensile Strength1 7.0 MPa DIN 53504/ISO 37
Elongation at Break1 800 % DIN 53504/ISO 37
Tear Resistance 15.0 N/mm ISO 34-1 Methode B (b) (Graves)
CS 72 h/23 °C 29 % DIN ISO 815-1 Method A
CS 24 h/70 °C 41 % DIN ISO 815-1 Method A
CS 24 h/100 °C 73 % DIN ISO 815-1 Method A
Flow Spiral [760 bar, 200 °C] 95.0 cm DSOP Lab 2032
1Deviating from ISO 37 standard test piece S2 is tested with a traverse speed of 200 mm/min.
 
Tested on 2 mm sample plaque, under artificial weathering according to PV3930 with two year cycles, the color change is > 4 on greyscaleVW3930 weathering for warm and humid conditions:Test time 1600 h / Rel. moisture 60 to 80 % / Temperature of sample compartment 35 °C to 45 °C / Radiation dosage 350 MJ/m²
All values published in this data sheet are rounded average values.
The product storage life is 12 months after delivery if storage instructions are followed. Store under dry conditions at room temperature (15–30 °C) away from heat sources and direct sunlight! Contact with nitrogen oxides must be avoided during storage!
For further information and individual custom solutions please contact our customer service.

Processing Guideline Injection Molding
Cylinder Temperature 180 - 200 - 220 °C, max. 250 °C (360 - 390 - 430 °F, max. 480 °F)
Hotrunner Hot runner temperatures: 200 -250 °C (390 - 480 °F). The runner should be empty after a maximum of 2 - 3 shots.
Injection Pressure 200 - 1000 bar (2900 - 14504 psi) (depending on the size and weight of the part).
Injection Rate In general, the fill time should not be more than 1–2 seconds.
Hold Pressure We recommend to derive the optimum hold pressure from determining the solidification point, starting with 40 % - 60 % of the required injection pressure.
Back Pressure 20 - 100 bar; if color batches are used, higher back pressure is necessary.
Screw Retraction If an open nozzle is used processing with screw retraction is advisable.
Mold Temperature 25 - 40 °C (77 - 104 °F)
Predrying Pre drying of the material is not necessary; if surface moisture forms as a result of changes in temperature, the material should be dried for 2 - 4 hours at 60 - 80 °C (140 - 175 °F).
Needle Valve With materials < 50 Shore A the use of a needle valve is advisable.
Screw Geometry Standard 3-zone polyolefine screw.
Residence Time The residence time is to be set as short as possible with a maximum of 10 minutes.
Cleaning Recommendation For cleaning and purging of the machine it is appropriate to use polypropylene or polyethylene. Machine must be PVC-free.
The product storage life is 12 months after delivery if storage instructions are followed. Store under dry conditions at room temperature (15–30 °C) away from heat sources and direct sunlight! Contact with nitrogen oxides must be avoided during storage!