Hardness-dependent post-industrial recycled content; applications with demands on UV resistance; adhesion to PP

Processing Method:
Injection Molding
Color / RAL DESIGN:
black
Recycled raw materials content**:
24%
Availability:
Globally
Manufacturing Site:
Germany

Typical applications

  • Automotive Exterior
  • Applications for new mobility
  • Underbody applications
  • Cowls gaskets
  • Water deflectors
  • Air guide elements
  • Active Grill Shutter (AGS)
  • Covers

 

Material features

  • Weather resistant, suitable for automotive exterior
  • Recycled raw material content
  • Adhesion to PP
  • Low density
  • Recycling-specific raw material influences are possible

 

Regulations / Approvals

  • PV 3930 Florida (1 year)
  • PV 3930 Florida (2 years)
  • PV 3929 Kalahari (1 year)
  • PV 3929 Kalahari (2 years)
  • VW 50123
  • BMW GS 93042
  • Mercedes-Benz DBL 5562

 

X

SHARE FILE

Send
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
Please choose language of datasheet
PDF file - 1MBEnglish
PDF file - 1MBDeutsch
PDF file - 1MB中文
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MBItaliano
Americas (English) PDF fileSafety Data Sheet
Asia (English) PDF fileSafety Data Sheet
Asia (中文) PDF fileSafety Data Sheet
Asia (한국어) PDF fileSafety Data Sheet
Asia (日本語) PDF fileSafety Data Sheet
Value Unit Standard
Hardness 75 Shore A DIN ISO 48-4
Density 0.940 g/cm3 DIN EN ISO 1183-1
Tensile Strength1 11.0 MPa DIN 53504/ISO 37
Elongation at Break1 680 % DIN 53504/ISO 37
Flow Spiral [760 bar, 200 °C] 70 cm DSOP Lab 2032
Recycled raw materials content 24 %
1Deviating from ISO 37 standard test piece S2 is tested with a traverse speed of 200 mm/min.
**Recycling-specific influences such as slight color deviations, gloss differences, viscosity variations or a higher hardness spreading are possible with TPEs containing a recycled component.
An application-specific technical delivery agreement is therefore recommended.
All values published in this data sheet are rounded average values.
The expected shelf life of the TPE granules is a minimum of 24 months from the date of delivery, provided that the storage instructions are followed and the product is kept in the unopened original KRAIBURG TPE packaging.
Dry conditions at room temperature (below 40 °C/ 104 °F), away from heat sources and direct sunlight, must be maintained for proper storage. Contact with nitrogen oxides during storage should be avoided.
For further information and individual custom solutions please contact our customer service.

Processing Guideline Injection Molding
Cylinder Temperature 180 - 200 - 220 °C, max. 250 °C (360 - 390 - 430 °F, max. 480 °F)
Hotrunner Hot runner temperatures: 200 -250 °C (390 - 480 °F). The runner should be empty after a maximum of 2 - 3 shots.
Injection Pressure 200 - 1000 bar (2900 - 14504 psi) (depending on the size and weight of the part).
Injection Rate In general, the fill time should not be more than 1–2 seconds.
Hold Pressure We recommend to derive the optimum hold pressure from determining the solidification point, starting with 40 % - 60 % of the required injection pressure.
Back Pressure 20 - 100 bar; if color batches are used, higher back pressure is necessary.
Screw Retraction If an open nozzle is used processing with screw retraction is advisable.
Mold Temperature 25 - 40 °C (77 - 104 °F)
Predrying Pre drying of the material is not necessary; if surface moisture forms as a result of changes in temperature, the material should be dried for 2 - 4 hours at 60 - 80 °C (140 - 175 °F).
Needle Valve With materials < 50 Shore A the use of a needle valve is advisable.
Screw Geometry Standard 3-zone polyolefine screw.
Residence Time The residence time is to be set as short as possible with a maximum of 10 minutes.
Cleaning Recommendation For cleaning and purging of the machine it is appropriate to use polypropylene or polyethylene. Machine must be PVC-free.
The expected shelf life of the TPE granules is a minimum of 24 months from the date of delivery, provided that the storage instructions are followed and the product is kept in the unopened original KRAIBURG TPE packaging.
Dry conditions at room temperature (below 40 °C/ 104 °F), away from heat sources and direct sunlight, must be maintained for proper storage. Contact with nitrogen oxides during storage should be avoided.