VS/AD/HM Series

THERMOLAST® K

The VS/AD/HM series is your material solution for applications with velvety surfaces and wear high resistance requirements. It convinces by its adhesion properties to polar thermoplastics as well as by its resistance to nonpolar substances, especially sebum skin grease and skin oils. The compounds are available in black and natural colors. Natural color variants can be colored in many different ways.

Processing Method: Injection Molding, Extrusion
Color / RAL DESIGN: Natural, Black

Typical applications

  • Automotive Interior
  • Remote controls
  • Cell phone covers
  • Ear phones
  • Handles (tools and power tools, etc.)
  • Cosmetic packaging
  • Soft touch surface (thumb wheels, push buttons, switches)
  • Wearables
  • Function and design elements
  • Car mats

 

Material advantages

  • Adhesion to PA6 and PA12
  • Adhesion to PC, ABS, PC/ABS, ASA, SAN
  • Soft, velvety feel
  • Abrasion resistance
  • Scratch resistance
  • Optimized mechanical properties
  • Resistance to skin oils, sunscreen or olive oil
  • Halogen content (chlorine + bromine) < 900 ppm

 

Regulations / Approvals *

  • VW 50123
  • BMW GS 93042
  • Mercedes-Benz DBL 5562
  • Stellantis B62 0300
  • Renault 03-10-104
  • Stellantis MS-DC-242
  • UL 94 HB
  • ISO 10993-10 (Skin irritation)
  • TESLA TM-1010

 

Please choose language of datasheet
PDF file - 1MBDeutsch
PDF file - 1MBEnglish
PDF file - 1MBEspañol
PDF file - 1MBFrançais
PDF file - 1MBItaliano
PDF file - 1MB日本語
PDF file - 1MB한국어
PDF file - 1MBPolski
PDF file - 1MB中文
X

SHARE FILE

Send
Compound name
Color / RAL DESIGN
Hardness
DIN ISO 48-4
Shore A
Density
DIN EN ISO 1183-1
g/cm3
Tear Resistance
ISO 34-1 Method B (b)ISO 34-1 Method B (b) (Graves)
N/mm
Tensile Strength 1
DIN 53504/ISO 37
MPa
Elongation at Break 1
DIN 53504/ISO 37
%
Adhesion to PC 2
VDI 2019 two-component injectiVDI 2019 two-component injection molding
N/mm
Flammability
49 CFR §571.302 (FMVSS 302)
mm/min
Odor
VDA 270 B-3
NOTE
Fogging
DIN 75201-B
mg
Thermal desorption – VOC
VDA 278
µg/g
Thermal desorption – Fog
VDA 278
µg/g
Color fastness 3
DIN EN ISO 105-B06 Method 3
GS
TC4CEN Natural 40 1.120 8.0 14.1 800 5.0 (C) - - - - - -
TC4CEZ Black 40 1.110 7.5 16.0 750 4.1 (C) 56 2.5 0.73 196 557 4.5
TC5CEN Natural 50 1.140 10.0 18.7 700 4.9 (C) - - - - - -
TC5CEZ Black 50 1.130 10.0 28.0 650 5.5 (C) 48 3.0 0.88 130 491 4.5
TC6CEN Natural 60 1.150 27.0 14.0 600 6.0 (C) - - - - - -
TC6CEU Natural 60 1.110 18.5 12.0 550 5.5 (D) 61.3 <3.5 0.68 <250 <1500 4
TC6CEZ Black 60 1.150 27.0 14.0 600 6.0 (C) 53.4 3 0.79 181 419 4.5
TC7CEN Natural 70 1.190 30.0 19.0 650 10.0 (D) - - - - - -
TC7CEU Natural 70 1.130 26.1 15.0 500 8.0 (D) 59.9 3 0.58 133 332 3.5
TC7CEZ Black 70 1.190 30.0 19.0 650 10.0 (D) 41.4 3.5 0.41 184 370 4.5
TC8CEN Natural 80 1.200 35.0 18.0 580 9.0 (D) - - - - - -
TC8CEU Natural 80 1.170 35.9 16.0 500 4.5 (A) 59.1 <3.5 0.71 <250 <1500 4
TC8CEZ Black 80 1.200 35.0 18.0 580 9.0 (D) 40 2.5 0.37 121 944 4.5
1Deviating from ISO 37 standard test piece S2 is tested with a traverse speed of 200 mm/min. Specimens were tempered for 20 hrs at 100°C (212°F).
2The adhesion quality depends on mold design, product geometry and process parameters.
3Rating after 5 cycles; acc. to DIN EN 20105-A02
 


TC6CEN passed tests for skin irritation according to ISO 10993-10.
All values published in this data sheet are rounded average values.
The shelf life of the TPE granules is 24 months from delivery if storage instructions are observed and the product is stored in the unopened original KRAIBURG TPE packaging. Store in dry conditions at room temperature (below 40 °C) away from heat sources and direct sunlight! Contact with nitrogen oxides must be avoided during storage!
For further information and individual custom solutions please contact our customer service.
* Regulations a compound complies with and approvals granted are displayed here. Please note: All regulations and approvals for all compounds of a series are collectively shown in the overview of the respective product series, i.e. not all regulations and approvals shown in the overview apply to each individual compound.